![]() You don’t have to pull cables from the mainboard to the printhead for each element, or cobble together cables somewhere with the soldering iron. If necessary, you can replace the entire printhead. I like it when the wire harness plugs into a connector on the printhead. The printhead is neatly assembled and preassembled and makes a valuable first impression. I haven’t quite risen to the question of whether the roll should deliver the filament from below or from above. The sensor is mounted directly on the extruder and has a strange angle for my taste. In addition, a filament runout sensor is also included. With very small rolls, the strong axis of the bracket is likely to cause a problem. The holder is so large that normal rolls can also be placed on it. The scope of delivery also includes a holder for the filament rolls. If you will not be using the printer in the living room or right next to or on the desk, the background noise is okay. See our guide on the best 40mm fans for 3D printers. In this case, you can install quieter fans. Therefore, the printer cannot be made quieter without completely replacing the mainboard by installing quieter drivers. The mainboard has permanently integrated drivers on the circuit board. The lack of a cover on the underside makes the fan in the power supply noisy during printing operations. The rest of the processing of the printer is also exemplary. No cable was disconnected or looked to be in any way. The wiring is fine to my non-electrician mind. If you put the printer on a screwdriver or the like, a short circuit or the like could very quickly occur. That is why the bottom of the photo above is also green, because any LED on the circuit board is green.įor my part, the lack of cover on the underside does not seem right. This time I didn’t have to bother to unscrew the printer because there is no cover on the bottom. Therefore, roughly speaking, only the axles have to be mounted and the motors connected to the wiring harness. The electronics are located at the bottom of the housing. Assembly Processįor the most part, the assembly is quite simple and can be done in 30-60 minutes. So a couple of screws and a small sensor are also included twice in the scope of delivery. There is a little spare material for that. Tweezers and the usual blue pliers are missing. Apart from that, the necessary tools, a card reader and a small spatula are included in the scope of delivery. The screws are exemplary packed in labeled bags. After unboxing the package, you can start assembling the device either according to instructions on the manual or the video instructions. ![]() Only the electronics are already installed in the lower housing.Īpart from that, the items are packed in the usual Tetris manner. The structure is a bit more extensive, since the printer is not delivered pre-assembled to a large extent. A variety of screws packed in well-labeled bags.Version: V2.0 Beta 6 Released: 17th June 19 Changelog: First beta with fully working core features.When you purchase the JGMaker Magic 3D printer review, this is what you’ll get in the box:.Version: V2.0 Release Released: 29th July 19 Changelog: Updated marlin build, initial public facebook release.Version: V2.0A Released: 1st Aug 19 Changelog: Fixed saving settings to SD. ![]() ![]() Version: V2.0C Released: 3rd Aug 19 Changelog: Fixed loading settings from SD at startup.Version: V2.0D Released: 4th Aug 19 Changelog: Fixed first time initialisation of SD eeprom.dat file.Version: V2.0E Released: 23rd Dec 20 Changelog: Updated Marlin 2.0.6.3 build.Version: V2.0F Released: 25th Dec 20 Changelog: Merry Christmas - a new user interface has arrived! EEPROM is saved to CPU flash.Version: V2.0G Released: 25th Dec 20 Changelog: Filament Runout sensor support added! (Note: screen bootup still says 2.0F - oops!).Power outage support added (writes to SD card). Version: V2.0H Released: 10th April 21 Changelog: Built on latest marlin 2.0.x buxfix commit.JGMaker A1 Download Latest Stable Version: 2.0Hĭownload Official OEM Factory Firmware (Latest A1: 11th July 2019) Thank you, and happy printing! ❤☕☺ Download Previous Stable Version: 2.0Dĭownload Official OEM Factory Firmware (Latest A5S: 27th April 2021) If you would like to support my work, you can send me a coffee here. Now that all the original features are working, this will probably be my last firmware release for these printers. Polish / Polski ( zadowoleni użytkownicy).French / Français ( utilisateurs heureux).German / Deutsch ( zufriedene benutzer).JGMaker A5S Download Latest Stable Version: 2.0H
0 Comments
Leave a Reply. |